TSAUTOP 3.94*2.3*2.79(ft) DIY Hydro Dipping Tank From China
Feature: 1.2m small DIY Hydro Dipping Tank
Outside Size L: 1.2m x W:0.7mx H:0.85m (3.94*2.3*2.79(ft))
Material: 201# Stainless Steel T=2mm+-0.2mm
Main Components: Heating Elements 220V, Single Phase, 50 HZ, 6KW
Water Re-circulation System
Pump Power: 220V, Single Phase, 50 HZ, 375W
Control Panel:
1. Master Power On/Off Switch
2. Pump On/Off Switch
3. Heating Element On/Off Switch
4. Knob switch with lamp
N.W.: 100kg,
G.W.: 130kg, 1.5cbm
Item NO. | TSHDT1200 | TSHDT2400 | TSHDT3000 |
Machine Size | Overall Dimensions | L: 120CM X W: 70CM X H: 85CM | L: 240CM X W: 120CM X H: 85CM | L: 300CM X W: 120CM X H: 85CM |
L: 47.2 Inch X W: 27.5 Inch X H: 33.5Inch | L: 94.5 Inch X W: 47.2 Inch X H: 33.5Inch | L: 118.1 Inch X W: 47.2 Inch X H: 33.5Inch |
Dipping Area dimensions | L: 80CM X W: 60CM X H: 70CM | L: 200CM X W: 100CM X H: 70CM | L: 260CM X W: 100CM X H: 70CM |
L: 31.5Inch X W: 23.6 Inch X H: 27.6 Inch | L: 78.7 Inch X W: 39.3 Inch X H: 27.6 Inch | L: 102.3 Inch X W: 39.3 Inch X H: 27.6 Inch |
Machine Material | Thickness =2.5mm+-0.2mm 201#Stainless Steel |
Machine Main Components | Heating Elements | 1Set, 208-240V, Single Phase, 50 HZ, 6000W | 2 Sets, 208-240V, Single Phase, 50 HZ, 6000W*2 |
Water Recirculation System | Stainless Pump, 220V, Single Phase, 50 HZ, 375W | Stainless Pump, 208-240V, Single Phase, 50 HZ, 750W |
Control Box | 1. Master Power On/Off Switch | 1. Master Power On/Off Switch |
2. Pump On/Off Switch | 2. Pump On/Off Switch |
3. Heating Element 1# Switch | 3. Heating Element1# &2# Switch |
4. Digital Thermostat X 1 PCS | 4. Digital Thermostat X 2 PCS |
5. Knob switch with lamp | 5. Knob switch with lamp |
6. Digital Timer and Buzzer | 6. Digital Timer and Buzzer |
7. E-stop | 7. E-stop | |
Water Capacity | 0.7ton | 1.7 Tons | 2.5 Tons |
Package | Fumigation-free Plywood Case |
Net WT | 80kg | 240kg | 320 KG |
Gross WT | 130kg | 280kg | 370KG |
Package Size | L: 130CM X W: 80CM X H: 110CM | L: 250CM X W: 130CM X H: 110CM | L: 310CM X W: 130CM X H: 110CM |
L: 51.2 Inch X W:31.5 Inch X H: 43.3inch | L: 98.4 Inch X W:51.1 Inch X H: 43.3inch | L: 122.0 Inch X W:51.1 Inch X H: 43.3inch |
TSAUTOP® 1.2m Small DIY hydro dipping tank with CE certification is a simple, safe, useful, eco, and efficient hydrographic equipment. It is a key piece of equipment for the whole water transfer solutions. It is very suitable for hydro dipping for beginners or hydro dip at home.

It is the key equipment for the whole hydro dipping process for dipping 0.5m wide hydrographic film. It is very suitable for DIY hydro dipping, training, practice, demo, and teaching.
TSAUTOP® 1.2m Small DIY hydro dipping tank has a superb welding process and a humanized structural design. All welded parts are welded with 304 stainless steel welding wire. All the welding marks are polished to ensure no leaks. So, it can guarantee no water leakage for 5 years.

TSAUTOP® 1.2m Small DIY hydro dipping tank is equipped with 2pcs wiper and partition beam, can wipe the film slag and divide the dipping area into few small areas, ensure the film does not expand too much.

TSAUTOP® 1.2m Small DIY hydro dipping tank is designed as two parts dipping tank, filter, and heating tank. It ensures enough dipping area and fast heating.
The dipping area size is 80cm*60cm*70cm, so it fits for hydro dipping shoes, hydro dipping guns, hydro dipping wheels, hydro dipping helmet, hydro dipping car parts, hydro dipping dashboard, hydro dipped guitar, hydro dipping tumblers, hydro dip cups, hydro dipping sneakers, hydro dip rifle, hydro dipped controller, hydro dipping hard hat and so on.


TSAUTOP® DIY Hydro Dip Tank has good quality and high-power heating element.1.2m tank has a 1set 6kw heating element. This can ensure fast-heating in 30minutes.

TSAUTOP® DIY Hydro Dipping Tank is made of 2.5mm thick 201 stainless steel, framed of 2mm thick 304 stainless steel square pipe, and equipped with 6pcs universal wheels and thick feet.
All of these ensure that the hydro dip tank can hold enough water without deformation. Thick stainless steel can ensure to resist acid, alkali, salt, and corrosion. All of these ensure TSAUTOP® hydro dipping tank’s long life.

There have 1 piece thermostats on the control box and 1piece temperature sensors, the temperature of the dipping tank and heating tank can be set and monitored in real-time. When the temperature reaches the preset temperature, the heating element will stop to heat water, this will save your power.

In the normal, the temperature will set 25-35℃. Certainly, you can turn on all or one or nothing according to your local temperature.
TSAUTOP® DIY Hydro Dip Tank is equipped low-noise, strong-flow, and long-life stainless-steel water pump, ensure flush the film slag. 375W pump for the 1.2m tank.

We can make the dip tanks with various voltages as your requirements, such as single-phase 110v,220v,3phases 220v,380v, or the other special voltages.
The electric box and wires of TSAUTOP® DIY Hydro Dip Tank are equipped safely. All working units are equipped with circuit breaker protection switches and emergency stop switch, ensure the safety of humans and machines in the emergency.
There has a digital timer and a buzzer on the control box. you can set the dipping time to alarm you.

All wires are concealed and packed with protective pipes to prevent electrical leakage. All tanks have equipped with earth wire to avoid electric shock.
There have some high-pressure spray nozzles at the end of the water outer to ensure the water is flushed farther.

TSAUTOP® DIY Hydro Dip Tank is easy to install and operate. The electrical wire connecting is simple. Each wire sticks a number, you connect the wire as the number. We have wired all cables with a quick power connector. So you just need to enter your main power.

All Tanks are packed with a Fumigation-free wooden box for avoiding damage during transportation.

We supply a detail manual book. We have different dimensions hydrographic tank, you can choose the suitable one according to your working items.
TSAUTOP® 4*2.3*2.79(FT) DIY HYDRO DIPPING TANK TSDT1200
USER GUIDE

Attention please:
Please read the below at first after receiving the wooden box:
1. When you open the wooden case with TSAUTOP® 4*2.3*2.79(ft) DIY Hydro Dipping Tank, please use the Rolling Wheel to move; if you want to move the DIY Hydro Dipping Tank with one forklift, please mind that DON’T let the forklift arm HIT/TOUCH the OUTLET TUBE (welded metal type) under the hydro dipping tank; it will Probably lead the tube bent and can’t fit the pipe tightly;
2. When you install the PVC pipe, strongly suggest use Teflon Tape to increase the leakproof; refer to the below photo.

3. When you want to wire, please ask help from one PROFESSIONAL ELECTRICIAN, to be on the safe side. Wrong wiring can lead to danger and pump/electric parts damage;
4.NEVER let the pump run in the air WITHOUT water; That will easily lead to pump damage; Fill enough water according to the instruction in this manual before launching the pump;
5. Before fill water to the DIY Hydro Dipping Tank, for the first usage, it’s better to use some Glass cement (Very common paste to water-proof) to the welding seam
CHAPTER 1.GENERAL DESCRIPTION
TSAUTOP® 4*2.3*2.79(ft) DIY Hydro Dipping Tank is one of our hydrographics equipment which is used for hydro dipping, this hydrographics equipment has an automatic constant temperature, timer switch, blow film, water circle, automatic filter film dust features….
Heating function, setting different temperature according to the different hydro dipping film, and with the automatic constant temperature controller.
Timer Switch, setting different dipping time according to the different hydro dipping film, the buzzer will alarm till the settled time, indicating procedure of spraying activator.
Flushing film function, starting flush film after hydro dipping completed, instantly remove the remaining hydro dipping film dust, preparing for next putting hydro dipping film.
Water circle and filtering, over film dust, will be filtered and circle till the surface of the hydro dipping tank for maximum saving the water.
Control Box Commentary

- Power Light:Power indicating lights
- Power Switch::Turn left ,Power Light(Yellow)OFF,POWER OFF,Turn Right,Power Light(Yellow)On,Power activating
- Timer Light:Time indicating lights
- Timer Switch :Turn left,Timer Light(Green)OFF,Timer switcher off power,Turn right timer switch,Timer Light(Green) on,timer switcher activating。Timer switch upper panel indicating current time,lower panel indicating current settled time,after reaching resettled time,,Buzzer alarming,any changes on setting,press decreasing an increasing key for decreasing or increasing time.
- Heater 1# and 2# Light:6KW and 12kw Heating indicating lights
- Digital Timer:Time controller
- Heater 1# &2# Switch:Turn left,6KW Heating Light(Yellow)OFF,Turn Right,6KW Heating Light(Green) If turn on two switches, the two heaters are working, the total power is 12kw.
- Heating switch upper panel indicating current water temperature,lower panel indicate presetting water temperature,any changes to water temperature,press left key 5seconds, the down digital will flash and press up or down for adjusting the water temperature setting
- Buzzer:TIMER ALARM
- E-STOP:Emergency Switch, Emergency Switch all functions.
Parameter (the following data is the default configuration)
Input Voltage:single phase 220V/3 phases 220v/380v
Power Consumption:12.75kw, the heater power 6kw each, water pump power 0.75kw
Working Temperature:25-30℃
CHAPTER 2. INSTALLATION
1.Power inlet wiring for SINGLE phases, 220VAC :
We already finish most wiring before shipment according to your special voltage requirement; Please don’t change them.
Connect the wires according to the NUMBER in the wires and switch, such as wire 1 to Number 1 place. Refer to the below photo:

Detail: Please attention to the wire with “+” & the wire with “-“ to the right place. Otherwise, the temperature can’t be shown properly in “Digital Thermostat” meter.
2.Power inlet wiring for 3 phases, 220V AC AND 3 phases, 380-415V AC :
1) We already finish most wiring before shipment according to your special voltage requirement; Please don’t change them.
2) Connect the wires according to the NUMBER in the wires from a proper sequence 01,02,03,1, 2,……10; From left the first place to the right in sequences; Refer to the below photo:

Please attention: The input cable is provided by the user. Must connect 3 live wires to the left 3 holes and null wire to “N” hole as in the below photo.
Check everything OK according to the operation manual and then connect 5 INPUT POWER SUPPLY wires well as the arrow point at in the below photo:
Power inlet wiring

Important reminder:
You will fill enough water into the tank before you start the hydro dipping machine.
The water level is level with the height of the partition.

If you start the hydro dipping machine, the water pump doesn’t work or reverse (small water flow),please stop the machine at once,you can change any 2 live wires sequence(U V W) to solve this problem.

U V W: Inlet 3phase living wires | B1: Big water tank K Mode Heating Couple |
U1 V1 W1:Water Circle Tank Heating 3phase Wiring | B2: Small Dipping tank K mode Heating Couple |
U2 V2 W2:Water Circle Tank Heating 3phase Wiring | |
U3 V3 W3:Water Pump 3phase wiring | |
Water pump motor Connection for 3phases 220v:
Water pump motor Connection for 3phases 380v:

Chapter 3. Setting and Using
1、Settings Temperature Controller
 | A:Current temperature indicatingB:Presetting temperature indicating C:presetting temperature adjustment Press←for setting Press↑for increasing Press↓For decreasing Repress←For saving setting |
Time Switch
 | A:Counted time indicatingB:Presetting Time indicating Adjusting time according to hundred bits, ten bits, digital bits Press﹢For increasing Press﹣For decreasing |
2.Operating
(1) Machine Checking before the start.
A、TURN OFF outlet water pipes of working water tank and circle water tank,
1) Inpour clear water to the working water tank till the Central position of water jet Nozzle :

2) remove the Net Metal cover, Inpour clear water to the circle water tank till to a little lower than the surface of the metal cover. Then put back the cover.
Attention:
A.Should fill enough water to avoid the water transfer pump exposed to the air. If the pump works in the air, the pump will EASILY be damaged.

B、Open Power Box, Turn on air-break switch,Power indicating lights on (red);
C、Turn right and power on power,Power indicating lights on(green)
D、Turn right and power on heating switch for working water tank and circle water tank, presetting water temperature.
E、Turn right and power on water pump,checking water pump working conditions;
F、Turn left and power off water pump, Turn right and power on timer switch,Turn right and power on timer switcher,adjusting time,reaching adjusted time for checking buzzer working conditions.
G、Press E-Stop,checking all indicating lights、temperature controller and timer switch power off or not;
H、Machine testing completed, Clockwise turning E-stop, Power on the machine.
(2). Hydro dipping process
A、Power on the machine, setting proper water temperature for working water tank and circle water tank;
B、Reaching settled water temperature for the working tank and circle tank, turn on the water pump, and blow remaining dust of working tank till automatic filtering area. Power water pump, still working water tank water no water wave, fitting water transfer film, and power timer switch.
C、Buzzer alarming, spraying activator on water transfer film smoothly, waiting till water transfer film melt and start water transfer printing procedure, switch off timer switcher after transfer completed.
D、Power on the water pump, blowing remaining dust film till filtering area, and start next water transfer printing job.
Chapter 4. Common Problems and Solutions
Without Power | 1.Checking E-Stop Switch On/OFF status2.Checking the inlet wiring voltage 3.Checking air-break switch at On status 4.Checking Power input switch |
The heater does not work,but indicate temperature | 1.Checking Heating Wiring status2.Checking Heating pipe damage or not |
The heater does not work, no indicating temperature | 1.Checking Heating switch at On status2.Checking Temperature controller Wiring 3.Checking Temperature Controller damage or not |
Heater continuous working after temperature reaching the presetting temperature | 1. Check K mode Heating Couple Wiring2. Check if K Mode Heating Couple Damage 3. Check Temperature Controller damage or not |
Timer Switch does work | 1.Checking Timer Switch wiring2.Checking Timer Switch damage or not |
Timer Switch does work, Buzzer does alarm | 1.Checking Buzzer wiring2.Checking Buzzer damage or not |
The water pump does not work,indicating lights on | 1.Checking water pump wiring2.Checking water pump damage or stuck |
Machine working well, indicating lights off | Replacing indicating lights |
THE COMPLETE GUIDE FOR DIY HYDRO DIPPING
DIY Hydro dipping is a fantastic way to decorate any 3D item which can be submerged in water without harm. While there are many companies specializing in hydro dip art for large items (e.g. cars interior, airline interior, yacht, RV interior, and sports equipment), it’s possible to do the DIY hydro dipping process on your own with a home size hydro dip kits.
Step 1. Using a Hydro Dipping Kit
Purchase a kit. Look it online for a home hydro dip kit, which helps you to transfer a specific print or design onto a 3D object (that can be submerged in water without harm) without specialized equipment. In general, companies making these kits will offer an assortment of designs to choose from to customize your kit. Basic home hydro dip kits should include:
- Patterned film
- Activator
- Topcoat
- Basecoat
- Universal primer
Step 2. Choose a suitable DIY hydro dipping tank.
Most DIY kits do not come with a DIY hydro dipping tank to be used during the dipping process. So choose a watertight plastic, glass, or aluminum DIY hydro dipping tank which is deep enough to fully submerge the object you are dipping. Tasutop hydrographics have A4/A3/1.2m DIY hydro dipping tank. It should also be long and wide enough to leave 5-6 inches (approximately 12-15 cm) between the edge of the container and the object.
Step 3. Prepare the item.
Make sure that the item you are dipping is free of dust and debris. Spray on the item with the primer provided in your kit, enough to coat, but not enough for the primer to run. Apply 1-2 light coats of the base coat spray provided in your kit, and leave the item to dry for one or two hours.
Before applying the primer and base coat, use masking tape to block off any parts of the item that you do not wish to have an image printed on.
Step 4. Size and cut the hydro dipping film.
Measure the size of the object you wish to cover and add 4-5 inches (approximately 12-15 cm) on each side. Cut the film accordingly. Make sure that the film remains dry during this process, as getting it wet could cause the image to warp.
Place masking tape around the edges of the film to keep it from rolling.
Step 5. Set up the DIY hydro dipping tank.
Fill the container with hot (but not boiling) water, approximately ¾ of the way full. Carefully pick up the film and bring the opposite sides together, holding it like a sling. Place the bottom of the sling onto the middle of the surface of the water, and slowly bring the sides down to place the film flat on the water.
Step 6. Let the film hydrate and apply the activator.
Use your phone or a stopwatch to ensure that the film dissolves for sixty seconds. After the sixty seconds, spray the activator provided in your kit evenly over the film. Once coated, the film should take approximately 5-10 seconds to turn into liquid ink on the surface of the water.
- When the film is fully activated it will have a distinctly glossy appearance and will expand to fill the entire surface size of the container.
Step 7. Dip your item.
Hold your item at a 45-degree angle and slowly submerge it into the water. Once the item is fully submerged, even out the angle by pushing it down towards the ink. Keep your movements fluid for best results.
- Put on gloves before dipping your item. If they are not supplied in the kit, purchase a pair before starting the whole dipping process.
Step 8 Rinse the item.
Slowly remove the item from the water by rinse tank. Hold the item lightly and carefully, and avoid rubbing its surface. Rinse it under cold water immediately for approximately 3 minutes to remove any PVA residue.
Step 9.Apply the topcoat.
After air-drying the item, apply an even coat of the aerosol topcoat spray provided in your kit. Let the item air dry before applying the second coat. Continue the process until the finish is to your liking.